先頭に戻る

65V, 3.8A Dual Brushed or Single Stepper Motor Driver with Integrated Current Sense

業界最小の65Vシングルチャネルブラシ付きモータードライバおよびステッパソリューション

製品の詳細

主な特長

Parametric specs for DC Motor Drivers
No. of Drivers 2
Peak Motor Current (A) 3.8
VSUPPLY (V) (min) 4.5
VSUPPLY (V) (max) 65
Total RON (mΩ) (typ) 300
Direction Control Independent
Current Regulation Internal
Internal CR Reference Yes
Oper. Temp. (°C) -40 to +125
Package/Pins TQFN-CU/38
Budgetary
Price (See Notes)
2
非表示にする

簡易ブロック図

Technical Docs

サポートとトレーニング

技術質問への回答についてはナレッジベースで検索ください。

絞り込まれた検索

マキシムでは、お客様の技術的質問にお答えするため、アプリケーションエンジニアの専任チームも配置しています。 サポートセンター をご利用ください。

パラメーター

Parametric specs for DC Motor Drivers
No. of Drivers 2
Peak Motor Current (A) 3.8
VSUPPLY (V) (min) 4.5
VSUPPLY (V) (max) 65
Total RON (mΩ) (typ) 300
Direction Control Independent
Current Regulation Internal
Internal CR Reference Yes
Oper. Temp. (°C) -40 to +125
Package/Pins TQFN-CU/38
Budgetary
Price (See Notes)
2

主な特長

  • Two H-Bridges with 65V Maximum Operating Voltage
    • Total RON (High-Side + Low-Side): 300mΩ typical (TA = 25°C)
  • Current Ratings Per H-Bridge (Typical at 25°C):
    • IMAX = 3.8A (Impulsive Current for Driving Capacitive Loads)
    • ITRIP_MAX = 3A (Maximum Current Setting for Internal Current Drive Regulation)
    • IRMS = 2ARMS
  • Integrated Current Drive Regulation (CDR)
    • Internal Current Sensing (ICS) Eliminates External Bulky Resistors and Improves Efficiency
    • Current Drive Regulation Monitor Output Pins (CDRA and CDRB)
    • Multiple Decay Modes (Slow, Mixed, Fast)
    • Fixed Off Time Configurable with External Resistance.
  • Current-Sense Output (Current Monitor)
  • Fault Indicator Pin ( Actove-Low FAULT)
  • Protections
    • Overcurrent Protection for Each Individual Channel (OCP)
    • Undervoltage Lockout (UVLO)
    • Thermal Shutdown (TSD) TJ = +165°C
  • TQFN38 5mm x 7mm package (TSSOP38 4.4mm x 9.7mm available in the future)

アプリケーション/用途

  • ブラシ付きDCモータードライバ
  • ラッチバルブ
  • ソレノイドドライバ
  • ステッパモータードライバ

説明

The MAX22203 is a dual 65V, 3.8AMAX H-Bridge with PWM inputs and accurate Current Drive Regulation (CDR). Each H-Bridge can be controlled individually and has a very low typical RON (high-side + low-side) of 0.3Ω, resulting in high driving efficiency and low heat generation. The MAX22203 can be used to drive two Brushed DC motors or a single Stepper Motor.

The integrated CDR can limit the start up or stall the current of a Brushed DC motor or control the phase current for stepper operation.

The bridge output current is sensed by a non-dissipative Integrated Current Sensing (ICS) eliminating the bulky external power resistors (which are normally required for this function) and compared with a configurable threshold current (ITRIP). The ITRIP threshold can be set independently for the two full bridges by connecting the external resistors to pins REFA and REFB .

The maximum output current per H-Bridge is IMAX = 3.8A and is limited by the Overcurrent Protection (OCP) circuit. This current can be driven for very short transients and is aimed to effectively drive small capacitive loads. The maximum user-configurable current regulation threshold is ITRIP_MAX = 3A. The maximum RMS current (IRMS) per H-Bridge is 2ARMS on a standard JEDEC 4-layer board. The maximum RMS current can be limited by thermal considerations and depends on the thermal characteristic of the application (PCB ground planes, heat sinks, forced air ventilation, etc).

The MAX22203 features Overcurrent Protection (OCP), Thermal Shutdown (TSD), and Undervoltage Lockout (UVLO). An open-drain active low nFAULT pin is activated every time a fault condition is detected. During Thermal Shutdown and Undervoltage Lockout, the driver is tristated until normal operations are restored.

The MAX22203 is packaged into a small TQFN38 5mm x 7mm package.

簡易ブロック図

MAX22203:簡易ブロックダイアグラム MAX22203:簡易ブロックダイアグラム Zoom icon

Technical Docs

サポートとトレーニング

技術質問への回答についてはナレッジベースで検索ください。

絞り込まれた検索

マキシムでは、お客様の技術的質問にお答えするため、アプリケーションエンジニアの専任チームも配置しています。 サポートセンター をご利用ください。