製品の詳細
主な特長
アプリケーション/用途
簡易ブロック図
Technical Docs
データシート | CDMAセルラ/PCSシステム電源 | Jun 03, 2010 |
サポートとトレーニング
技術質問への回答についてはナレッジベースで検索ください。
絞り込まれた検索マキシムでは、お客様の技術的質問にお答えするため、アプリケーションエンジニアの専任チームも配置しています。 サポートセンター をご利用ください。
サンプルについて:
サンプルは、外部のADI Sample Siteでのご注文となります。選択したパーツはSample Siteログイン後、カートに引き継がれます。Sample Siteを初めて使用する際は、アカウント登録をお願いいたします。Sample Siteに関するご質問は、SampleSupport@analog.comまでお問合せください。
主な特長
- One 300mA Low-Noise LDO
- Four 150mA Low-Noise LDOs
- 45µVRMS Noise from 10Hz to 100kHz
- > 60dB Crosstalk Isolation Below 10kHz
- > 60dB PSRR Below 10kHz
- 125mV (max) Dropout (OUT1 at 200mA)
- 100mV (max) Dropout (OUT2–5 at 100mA)
- Programmable Output Voltages
- 1.8V to 3.3V in 32 Steps
- 140ms (min) Reset Timer
- SPI- or I²C-Compatible Serial Interface
- Push-On/Push-Off Control Logic
- Two 150mA General-Purpose Open-Drain Outputs
- Overcurrent and Thermal Protection (all LDOs)
- 1µA Shutdown Current
- 20-Pin Thermally-Enhanced TSSOP or TQFN Packages
アプリケーション/用途
- 2または3セルニッケル水素、ニッカド、またはアルカリシステム
- CDMA携帯/PCS端末
- ハンディターミナル
- パームトップコンピュータ
- PDA
- シングルセルLi+ (リチウムイオン)システム
説明
Each linear regulator features extremely low dropout voltage, specified at two-thirds of the maximum output current. LDO1 is rated for 300mA, while LDOs 2–5 are each rated for 150mA. All LDOs are optimized for low noise and isolation. Each LDO can be individually enabled and disabled through the serial port, as well as individually programmed to any of 32 voltages from 1.8V to 3.3V.
The MAX1798/MAX1798A/MAX1799/MAX1799As' wide 2.5V to 5.5V input voltage range makes them compatible with a wide range of input supplies, including a single Li+ cell battery. Both devices are available in thermally enhanced 20-pin TSSOP and TQFN exposed pad (EP) packages. Evaluation kits (MAX1798EVKIT and MAX1799EVKIT) are available to facilitate designs.
Technical Docs
データシート | CDMAセルラ/PCSシステム電源 | Jun 03, 2010 |
サポートとトレーニング
技術質問への回答についてはナレッジベースで検索ください。
絞り込まれた検索マキシムでは、お客様の技術的質問にお答えするため、アプリケーションエンジニアの専任チームも配置しています。 サポートセンター をご利用ください。
サンプルについて:
サンプルは、外部のADI Sample Siteでのご注文となります。選択したパーツはSample Siteログイン後、カートに引き継がれます。Sample Siteを初めて使用する際は、アカウント登録をお願いいたします。Sample Siteに関するご質問は、SampleSupport@analog.comまでお問合せください。