Top

+65V Simple Swapper Hot-Swap Switches

Product Details

Key Features

Parametric specs for Hot Swap Controllers
VIN (V) (min) 10
VIN (V) (max) 65
# Channels 1
Circuit Breaker/ Current Limit Current Limit
Fault Condition Control Latched Off
Positive/Negative Rail Positive
Features Integrated MOSFET
Undervoltage/Overvoltage Protection
Package/Pins SOIC (N)/16
Budgetary
Price (See Notes)
4.72
View Less

Simplified Block Diagram

Technical Docs

Data Sheet +65V Simple Swapper Hot-Swap Switches Jul 01, 2001

Support & Training

Search our knowledge base for answers to your technical questions.

Filtered Search

Our dedicated team of Applications Engineers are also available to answer your technical questions. Visit our support portal .

Sampling:
Selecting the Sample button above will redirect to the third-party ADI Sample Site. The part selected will carry over to your cart on this site once logged in. Please create a new account there if you have never used the site before. Contact SampleSupport@analog.com with any questions regarding this Sample Site.

Parameters

Parametric specs for Hot Swap Controllers
VIN (V) (min) 10
VIN (V) (max) 65
# Channels 1
Circuit Breaker/ Current Limit Current Limit
Fault Condition Control Latched Off
Positive/Negative Rail Positive
Features Integrated MOSFET
Undervoltage/Overvoltage Protection
Package/Pins SOIC (N)/16
Budgetary
Price (See Notes)
4.72

Key Features

  • Provides Safe Hot Swap for +10V to +65V Power Supplies
  • IEEE 802.3AF Compliant (MAX5917A)
  • Startup into 500µF Load (MAX5917A)
  • 280mA Current Limit for MAX5910
  • 567mA Current Limit for MAX5917A
  • 420mA Current Limit for MAX5917B
  • Zero-Current Load Detection
  • Integrated 2.2Ω Power FET
  • Status Output Reports Fault Conditions
  • Internal Switch-Protection Circuitry
  • Built-In Thermal Shutdown

Applications/Uses

  • Internet Appliances
  • IP Phones
  • Network Hubs, Switches, Routers
  • Network Hubs, Switches, Routers
  • Power-Over-LAN
  • Power-Over-MDI
  • Remote Power Distribution

Description

The MAX5910/MAX5917 are fully integrated hot-swap switches for positive supply rails. These devices allow the safe insertion and removal of circuit cards into live backplanes or ports without causing glitches on the backplane power-supply rail. They also monitor various circuit parameters and disconnect the load if a fault condition occurs, alerting the host with a logic-level active-low IFAULT output. The MAX5910/MAX5917 operate over a +10V to +65V input voltage range. They are designed to permit hot plugging of an internet appliance such as an IP phone but are not limited to that application.

During startup, an internal power FET regulates the current between the backplane power source and the load to 280mA for the MAX5910, 567mA for the MAX5917A, and 420mA for the MAX5917B. After startup, the FET is fully enhanced to reduce its on-resistance. To ensure robust operation, the MAX5910/MAX5917 contain built-in safety features that prevent damage to the internal FET. They include an enable input, which responds to positive logic signals (+3.3V or +5V), allowing the host system to disconnect the load.

The MAX5910/MAX5917 Simple Swapper™ hot-swap ICs monitor four parameters for fault conditions: undervoltage lockout (UVLO), power-not-good, zero-current detection, and thermal shutdown. These devices are available in the extended temperature range, -40°C to +85°C. The MAX5910 comes in an 8-pin SO package and the MAX5917A/B is available in a 16-pin SO package.

Simplified Block Diagram

MAX5910, MAX5917: Typical Operating Circuit MAX5910, MAX5917: Typical Operating Circuit Zoom icon

Technical Docs

Data Sheet +65V Simple Swapper Hot-Swap Switches Jul 01, 2001

Support & Training

Search our knowledge base for answers to your technical questions.

Filtered Search

Our dedicated team of Applications Engineers are also available to answer your technical questions. Visit our support portal .

Sampling:
Selecting the Sample button above will redirect to the third-party ADI Sample Site. The part selected will carry over to your cart on this site once logged in. Please create a new account there if you have never used the site before. Contact SampleSupport@analog.com with any questions regarding this Sample Site.