MAX8903A

2A 1-Cell Li+ DC-DC Charger for USB and Adapter Power

Delivers 4MHz Switching


Please check latest availability status for a specific part variant.

Description

The MAX8903A–MAX8903E/MAX8903G/MAX8903H/MAX8903J/MAX8903N/MAX8903Y are integrated 1-cell Li+ chargers and Smart Power Selectors™ with dual (AC adapter and USB) power inputs. The switch mode charger uses a high switching frequency to eliminate heat and allow tiny external components. It can operate with either separate inputs for USB and AC adapter power, or from a single input that accepts both. All power switches for charging and switching the load between battery and external power are included on-chip. No external MOSFETs, blocking diodes, or current-sense resistors are required.

The MAX8903_ feature optimized smart power control to make the best use of limited USB or adapter power. Battery charge current and SYS output current limit are independently set. Power not used by the system charges the battery. Charge current and SYS output current limit can be set up to 2A while USB input current can be set to 100mA or 500mA. Automatic input selection switches the system from battery to external power. The DC input operates from 4.15V to 16V with up to 20V protection, while the USB input has a range of 4.1V to 6.3V with up to 8V protection.

The MAX8903_ internally block current from the battery and system back to the DC and USB inputs when no input supply is present. Other features include prequal charging and timer, fast charge timer, overvoltage protection, charge status and fault outputs, power-OK monitors, and a battery thermistor monitor. In addition, on-chip thermal limiting reduces battery charge rate and AC adapter current to prevent charger overheating. The MAX8903_ is available in a 4mm x 4mm, 28-pin thin QFN package.

The various versions of the MAX8903_ allow for design flexibility to choose key parameters such as system regulation voltage, battery prequalification threshold, and battery regulation voltage. The MAX8903B/MAX8903E/MAX8903G also includes power-enable on battery detection. See the Selector Guide section in the full data sheet for complete details.

MAX8903A: Typical Operating Circuit MAX8677A is an integrated 1-cell Li+ charger and Smart Power Selector™ with dual (DC & USB) power inputs | Typical Operating Circuit Enlarge+

Key Features

  • Efficient DC-DC Converter Eliminates Heat
  • 4MHz Switching for Tiny External Components
  • Instant On—Works with No Battery or Low Battery
  • Dual Current-Limiting Inputs—AC Adapter or USB
    • Automatic Adapter/USB/Battery Switchover to Support Load Transients
    • 50mΩ System-to-Battery Switch
    • Supports USB Spec
  • Thermistor Monitor
  • Integrated Current-Sense Resistor
  • No External MOSFETs or Diodes
  • 4.1V to 16V Input Operating Voltage Range

Applications/Uses

  • Mobile Internet Devices
  • PDA, Palmtop, and Wireless Handhelds
  • Personal Navigation Devices
  • Portable Multimedia Players
  • Smart Cell Phones
  • Ultra Mobile PCs
Part NumberLithium Ion CellsProtected VIN
(V)
Charging VIN
(V)
Charge Rate Set byMax. ICHG
(A)
Charge TerminationCharge RegulationOper. Temp.
(°C)
Package/Pins
maxmax
MAX8903 12016
Preset
Resistor
2Min. Charge CurrentSwitchmode-40 to +85
See Data Sheet
See All Battery Chargers (79)
Pricing Notes:
This pricing is BUDGETARY, for comparing similar parts. Prices are in U.S. dollars and subject to change. Quantity pricing may vary substantially and international prices may differ due to local duties, taxes, fees, and exchange rates. For volume-specific and version-specific prices and delivery, please see the price and availability page or contact an authorized distributor.


MAX8903AEVKIT: Evaluation Kit for the MAX8903A, MAX8903B, MAX8903C, MAX8903D, and MAX8903Y
Device   Fab Process   Technology   Sample size   Rejects   FIT at 25°C   FIT at 55°C  

Note : The failure rates are summarized by technology and mapped to the associated material part numbers. The failure rates are highly dependent on the number of units tested.

Quality Management System >
Environmental Management System >

Related Resources


MAX20335
Wearable Charge Management Solution

  • Extend System Use Time Between Battery Charging
  • Easy-to-Implement Li+ Battery Charging
  • Minimize Solution Footprint Through High Integration

MAX17262
5.2µA 1-Cell Fuel Gauge with ModelGauge m5 EZ and Internal Current Sensing

  • ModelGauge m5 EZ
  • Low 5.2µA Operating Current
  • Integrated Current Sensing

MAX20332
USB Charger Detection with Integrated Overvoltage Protection

  • Consumes Less Power
  • Delivers USB Compliance and Flexibility
  • Facilitates System Design

MAX77640
Ultra-Low Power PMIC with 3-Output SIMO, 150mA LDO, and Power Sequencer

  • Compact, High-Efficiency Power Solution
  • 3-Output SIMO Extends Battery Life
  • Low Quiescent Current

MAX77641
Ultra-Low Power PMIC with 3-Output SIMO, 150mA LDO, and Power Sequencer

  • Compact, High-Efficiency Power Solution
  • 3-Output SIMO Extends Battery Life
  • Low Quiescent Current

MAX17263
Single/Multi-Cell Fuel Gauge with ModelGauge m5 EZ and Integrated LED Control

  • ModelGauge m5 EZ
  • Monitors Single Cell or Multiple-Series Cell Battery Pack
  • Integrated LED Control with Push-Button Input

MAX17261
5.1µA Multi-Cell Fuel Gauge with ModelGauge m5 EZ

  • ModelGauge m5 EZ
  • Low 5.1µA Operating Current
  • Monitors Multiple-Cell Battery Pack

MAX17260
5.1µA 1-Cell Fuel Gauge with ModelGauge m5 EZ and Optional High-Side Current Sensing

  • ModelGauge m5 EZ
  • Low 5.1µA Operating Current
  • Accurate Current Sensing

MAXREFDES96
MAXREFDES96#: Single-Battery Charger and Fuel Gauge with Boost for Arduino Platforms