DS2120B, DS2120E

Ultra3 LVD SCSI Terminator


Please check latest availability status for a specific part variant.

Description

The DS2120 Ultra3 LVD SCSI terminator is a low-voltage differential (LVD) terminator. If the device is connected in an LVD-only bus, the DS2120 uses LVD termination. If any single-ended (SE) or highvoltage differential (HVD) devices are connected to the bus, the DS2120 disconnects from the bus. This is accomplished inside the part automatically by sensing the voltage on the SCSI bus DIFFSENS line.

For the LVD termination, the DS2120 integrates two current sources with nine precision resistor strings. Three DS2120 terminators are needed for a wide SCSI bus.

Key Features

  • Fully Compliant with Ultra3, Ultra160, Ultra320, and Ultra2 (LVD only) SCSI
  • Provides Low-Voltage Differential (LVD) Termination for Nine Signal Line Pairs
  • Zero Temperature Coefficient Termination Resistors
  • Autoselection of LVD Termination
  • 5% Tolerance on LVD Termination Resistance
  • Low Power-Down Capacitance of 3pF
  • Built-In Mode Change Filter/Delay
  • On-Board Thermal Shutdown Circuitry
  • SCSI Bus Hot Plug Compatible
  • Applications/Uses

    • Network-Attached Storage (NAS)
    • RAID Systems
    • SCSI Cables
    • SCSI Host Bus Adapter (HBA) Cards
    • Servers
    • Storage Area Networks (SANs)
    Request Reliability Report for: DS2120B  DS2120E 
    Device   Fab Process   Technology   Sample size   Rejects   FIT at 25°C   FIT at 55°C   Material Composition  

    Note : The failure rates are summarized by technology and mapped to the associated material part numbers. The failure rates are highly dependent on the number of units tested.

    Quality Management System >
    Environmental Management System >

     
    Status:
    Package:
    Temperature:

    Related Resources


    MAX25430
    Automotive 100W USB-PD Buck-Boost Port Controller and Protector

  • USB-PD PHY That is TCPCI Standard for Use with Any Low-Cost I2C Master Such as Hub IC, MCU or SOC (MAX25430B)
    • Ground-Offset-Adjusted BMC PHY for Maximum Signal-to-Noise Ratio
  • Non-TCPC Versions Available for Protecting External USB-PD Controller (MAX25430A)
  • Integrated Buck-Boost Controller for External H-bridge
    • 4.5V to 36V Input Operating Range
    • Fixed PDO 5V, 9V, 15V, and 20V up to 5.0A
    • 220kHz, 300kHz, or 400kHz Switching Frequency

  • MAX25400
    Automotive Hi-Speed USB 2.0 Protector

    • Targeted Features for Optimized USB Performance
    • Robust for the Automotive Environment
    • Standards

    MAX25431
    Automotive 40V, 2.2MHz, H-Bridge Buck-Boost Controller

    • Meets Stringent Automotive Quality and Reliability Requirements
    • Efficient Solution in a Small Solutions Size
    • Low Quiescent Current Helps Designers Meet Stringent OEM Current Requirements

    MAX22517
    Self-Powered, Two-Channel, 3.5kVRMS Digital Isolator

    • Robust Protection in Small Footprint
    • Robust Galvanic Isolation of Digital Signals
    • Design Flexibility

    MAX22518
    Self-Powered, Two-Channel, 3.5kVRMS Digital Isolator

    • Robust Protection in Small Footprint
    • Robust Galvanic Isolation of Digital Signals
    • Design Flexibility

    MAX22519
    Self-Powered, Two-Channel, 3.5kVRMS Digital Isolator

    • Robust Protection in Small Footprint
    • Robust Galvanic Isolation of Digital Signals
    • Design Flexibility

    MAX33072E
    +3V to +5.5V, Polarity Invert RS-485 Half-Duplex Transceiver with ±65V Fault Protection, ±40V CMR, and ±40kV ESD

    • Integrated Protection for Robust Communication
    • High-Performance Transceiver Enables Flexible Designs

    MAX33073E
    +3V to +5.5V, Polarity Invert RS-485 Half-Duplex Transceiver with ±65V Fault Protection, ±40V CMR, and ±40kV ESD

    • Integrated Protection for Robust Communication
    • High-Performance Transceiver Enables Flexible Designs

    MAX20459
    Automotive High-Current Step-Down Converter with USB-C Dedicated Charging Port

    • One-Chip Type-C Solution Directly from Car Battery to Portable Device
    • Optimal USB Charging and Communication for Portable Devices
    • Low-Noise Features Prevent Interference with AM Band and Portable Devices

    MAX77958
    Standalone USB Type-C and USB Power Delivery Controller

    • Customizable Firmware
    • USB Type-C Support and USB-PD Support
    • Supports BC1.2 Legacy/Proprietary Charger Detection

    MAX14906
    Quad-Channel Industrial Digital Output, Digital Input

    • Per-Channel Configurability Enables Wide Range of Applications 
    • Fault Tolerant with Built-In Diagnostics
    • High Integration Reduces BOM Count and PCB Space 

    MAX22088
    Home Bus System (HBS) Compatible Transceiver

    • High Integration Reduces BOM and Footprint
    • Configurability Enables Flexible Design
    • Integrated Protection for Robust Communication

    MAX14829
    Low Power IO-Link Device Transceiver with Dual Drivers

    • Low Power Dissipation Reduces the Thermal Footprint for Small Sensors
    • Configurability and Integration Reduce SKUs
    • Selectable Driver Integrated Protection Enables Robust Communication