10-Bit, 11Msps, Full-Duplex, Analog Front-End

Ultra-Low-Power, Highly Integrated Transmit and Receive AFE with CDMA Filters

Please check latest availability status for a specific part variant.


The MAX19711 is an ultra-low-power, highly integrated mixed-signal analog front-end (AFE) ideal for CDMA communication applications operating in full-duplex (FD) mode. Optimized for high dynamic performance and ultra-low power, the device integrates a dual 10-bit, 11Msps receive (Rx) ADC; dual 10-bit, 11Msps transmit (Tx) DAC with CDMA baseband filters; three fast-settling 12-bit aux-DAC channels for ancillary RF front-end control; and a 10-bit, 333ksps housekeeping aux-ADC. The typical operating power in FD mode is 37.5mW/42.7mW at a 4.915MHz/11MHz clock frequency.

The Rx ADCs feature 54.8dB SNR and 74.2dBc SFDR at 1.875MHz input frequency with an 11MHz clock frequency. The analog I/Q input amplifiers are fully differential and accept 1.024VP-P full-scale signals. Typical I/Q channel matching is ±0.01° phase and ±0.01dB gain.

The Tx DACs with CDMA lowpass filters feature -3dB cutoff frequency of 1.3MHz and > 64dBc stopband rejection at fIMAGE = 4.285MHz at fCLK = 4.915MHz. The analog I-Q full-scale output voltage range is selectable at ±410mV or ±500mV differential. The output DC common-mode voltage is selectable from 0.86V to 1.36V. The I/Q channel offset is adjustable to optimize radio lineup sideband/carrier suppression. Typical I-Q channel matching is ±0.03dB gain and ±0.07° phase.

Two independent 10-bit parallel, high-speed digital buses used by the Rx ADC and Tx DAC allow full-duplex operation for frequency-division duplex applications. The Rx ADC and Tx DAC can be disabled independently to optimize power management. A 3-wire serial interface controls power-management modes, the aux-DAC channels, and the aux-ADC channels.

The MAX19711 operates on a single 2.7V to 3.3V analog supply and 1.8V to 3.3V digital I/O supply. The MAX19711 is specified for the extended (-40°C to +85°C) temperature range and is available in a 56-pin, thin QFN package. The Selector Guide at the end of the data sheet lists other pin-compatible versions in this AFE family. For time-division duplex (TDD) applications, refer to the MAX19705–MAX19708 AFE family of products.
MAX19711: Typical Operating Circuit MAX19711: Typical Operating Circuit Enlarge+

Key Features

  • Dual 10-Bit, 11Msps Rx ADC and Dual 10-Bit, 11Msps Tx DAC
  • Ultra-Low Power
    • 37.5mW/42.7mW at fCLK = 4.915MHz/11MHz, FD Mode
    • 24.3mW at fCLK = 11MHz, Slow Rx Mode
    • 34.5mW at fCLK = 11MHz, Slow Tx Mode
    • Low-Current Standby and Shutdown Modes
  • Integrated CDMA Filters with > 64dBc Stopband Rejection
  • Programmable Tx DAC Common-Mode DC Level and I/Q Offset Trim
  • Excellent Dynamic Performance
    • SNR = 54.8dB at fIN = 1.875MHz (Rx ADC)
    • SFDR = 75dBc at fOUT = 620kHz (Tx DAC)
  • Three 12-Bit, 1µs Aux-DACs
  • 10-Bit, 333ksps Aux-ADC with 4:1 Input Mux and Data Averaging
  • Excellent Gain/Phase Match
    • ±0.01° Phase, ±0.01dB Gain (Rx ADC) at fIN = 1.87MHz
  • Multiplexed Parallel Digital I/O
  • Serial-Interface Control
  • Versatile Power-Control Circuits
    • Shutdown, Standby, Idle, Tx/Rx Disable
  • Miniature 56-Pin Thin QFN


  • CDMA Data Cards
  • CDMA Handsets
  • Portable Communication Equipment

MAX19710EVCMODU: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
MAX19710EVKIT: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
MAX19711EVCMODU: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
MAX19711EVKIT: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
MAX19712EVCMODU: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
MAX19712EVKIT: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
MAX19713EVCMODU: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
MAX19713EVKIT: Evaluation Kits/Evaluation Systems for the MAX19710, MAX19712, and MAX19713
Request Reliability Report for: MAX19711 
Device   Fab Process   Technology   Sample size   Rejects   FIT at 25°C   FIT at 55°C   Material Composition  

Note : The failure rates are summarized by technology and mapped to the associated material part numbers. The failure rates are highly dependent on the number of units tested.

Quality Management System >
Environmental Management System >


Related Resources

Best-in-Class Optical Pulse Oximeter and Heart-Rate Sensor AFE for Wearable Health

  • Complete Dual-Channel Optical Data-Acquisition System
  • Excellent Top-End Dynamic Range > 91dB in White Card Loop-Back Test (Nyquist Sample-to-Sample Variance)
  • Extended Dynamic Range up to 110dB (Averaging and Off-Chip Filtering)