Keywords: heart rate monitor, SpO2, blood oxygen, pulse oximetry, blood oxygen level, oxygen saturation level, wearable, HRM, earbud, sensor, sensor module, LED, photodetector, PPG, photoplethysmography
Guidelines for SpO2 Measurement Using the Maxim® MAX32664 Sensor Hub
Pulse oximetry (percentage of SpO2 concentration in blood) has been used as a key health indicator for many decades. Although the original academic development was made in 1935, the modern basis for determining the SpO2 concentration using light sources and photosensor(s) was developed by Takuo Aoyagi and Michio Kishi in 1972. When commercially feasible, SpO2 concentration measurement devices have made huge gains in medical applications. Since 1987, the Standard of Care (SoC) for the administration of a general anesthetikc has included pulse oximetry. All modern hospital bedside equipment include an SpO2 module based on the same fundamentals, albeit with minor modifications.
However, these hospital-based devices are expensive and bulky, and in their current form, their use is limited to hospitals, health clinics, and some doctor’s offices. To enable individuals interested in tracking their body’s key health indicators, a solution that is both light enough to wear in comfort and cheap enough for a typical consumer to purchase is needed.
Maxim has a solution that functions as a drop-in module for wrist-worn health bands, as well as finger-based pulse oximetry devices. This application note covers the theory behind pulse oximetry as well as typical design and calibration processes needed to incorporate our solution into various wearable devices.
What is SpO2?
Hemoglobin (Hb) is an oxygen-transport protein in red blood cells (RBCs). The two main forms of Hb present in blood are oxygenated hemoglobin (oxy-hemoglobin, HbO2) and deoxygenated hemoglobin (deoxy-hemoglobin, RHb).
SpO2 is a measure of the peripheral capillary oxygen saturation. More specifically, SpO2 is an estimate of the amount of oxygen in capillary blood, which is described as a percentage of the amount of oxy-hemoglobin to total hemoglobin, expressed as follows:
where C[HbO2] and C[RHb] are the concentrations of HbO2 and RHb, respectively.
The Beer–Lambert law describes the attenuation of light with the properties of the material through which the light is travelling. According to the Beer-Lambert law,
where A is the attenuation, I0 is the incident light intensity, I is the received light intensity, ε(λ) is the molar extinction coefficient, C is the concentration of material, and d is the optical path length.
Considering the molecule compound of tissue, Beer-Lambert law can be extended as follows:
The Beer-Lambert law enables us to measure SpO2 by using the molar extinction coefficients of HbO2 and RHb.
Pulse oximetry is a tool used for the noninvasive measurement of blood oxygenation (i.e., SpO2. Pulse oximetry is based on two principles: modulation of transmitted light by absorption of pulsatile arterial blood and different absorption characteristics of HbO2 and RHb for different wavelengths.
Pulse oximetry can be classified as transmissive and reflective:
Figure 1 shows pulsatile arterial blood and other blood and tissue components.
Figure 1. A schematic of pulsatile arterial blood and other blood and tissue components.
The pulsatile arterial blood absorbs and modulates the incident light passing through the tissue and forms the photoplethysmographic (PPG) signal, as shown in Figure 2. The AC component of the PPG signals represents the light absorbed by the pulsatile arterial blood. This AC component is superimposed on a DC signal that captures the effects of light absorbed by other blood and tissue components (e.g., venous and capillary blood, bone, water, etc.). The ratio of the AC signal to the DC level is called the perfusion index (PI).
Note that the DC and AC components of the received PPG signals are different for different LED wavelengths. This is due to the different absorption characteristics of HbO2, RHb, and other tissue components for different wavelengths.
Figure 2. Photoplethysmographic (PPG) signals received by a photodiode from red and infrared LEDs.
Figure 3 shows the molar absorption coefficients of HbO2 and RHb. To measure SpO2, two LEDs with different wavelengths are required. In addition, these two wavelengths should be selected such that the molar absorption coefficients of HbO2 and RHb are well separated. A red LED at 660nm and an infrared LED at 880nm are commonly used in pulse oximetry.
Figure 3. Molar absorption coefficients of HbO2 and RHb.
For more information, a detailed theory of pulse oximetry and noninvasive SpO2 measurement can be found in Development of a fractional multi-wavelength pulse oximetry algorithm.
Optical Design Guides
Maxim provides two optical design guides for its customers:
SpO2 measurement is achieved by the following equation:
where R is determined by the following equation:
and a, b, and c are calibration coefficients. This section describes how to obtain these coefficients.
Why is Calibration Required?
The SpO2 measurement performance of a device must be verified before the device is released to the market. The U.S. Food and Drug Administration (FDA) suggests using standards presented in the following:
According to these regulations, manufacturers need to declare the calibration range, reference, accuracy, methods of calibration and range of displayed saturation level. Furthermore, for the performance assessment, the FDA requires at least 200 data points equally spaced over a saturation range of 70% to 100%. Test subjects should have different ages, gender, and skin tones. For instance, the FDA requires that at least 30% of the volunteers must have dark skin pigmentation. The overall error or the root mean square error (RMSE) must be below 3.0% for transmissive pulse oximetry and below 3.5% for reflective pulse oximetry.
Maxim’s hardware and algorithm gives FDA-grade SpO2 measurement performance for both finger (implemented on different mobile phones) and wrist (implemented on a wrist watch). However, the FDA requires that a performance analysis of the SpO2 measurement must be done with the whole system and not only with the sensor. Thus, each customer must verify the FDA-grade SpO2 measurement performance in their final products with the optical shield in front of the Maxim sensor.
In addition to the FDA regulations, the theoretical relation between R and SpO2 does not give a satisfactory SpO2 measurement accuracy due to ideal-case assumptions used in pulse oximetry and the different optical properties of the hardware (e.g., optical shield and wide light spectrum of LEDs). Figure 4 shows the theoretical R-curve and calibrated R-curves. The theoretical R-curve does not give accurate SpO2 values.
Figure 4. Theoretical and calibrated R-curves. All phones use the same sensor with different optical shields, which result in slightly different R-curves.
In addition, Figure 4 shows the effect of a cover shield in front of the sensor. Although, all phones use the same sensor, their calibrated R-curves are slightly different from each other. Thus, a calibration process is required to obtain calibration coefficients for better measurement accuracy by compensating for the deviations from the Beer-Lambert law and the non-idealities of the hardware. These coefficients are obtained after collecting comprehensive data in a 3rd party calibration lab.
In the calibration lab, the SpO2 level of the test subjects are varied in a controlled manner and the PPG signals measured from the test subjects are recorded. During data collection, the test subjects use a gas mask to control their SpO2 level. Through the gas mask, the blood oxygen content is reduced incrementally by changing the oxygen level of the test subject from 100% SpO2 and lowering to 70% SpO2. After collecting enough data according to the FDA regulations, the recorded PPG signals are used to find the R values. Then, a second (or first) order line is fitted to obtain the calibration coefficients a, b, and c for the SpO2 measurement algorithm, as shown in Figure 5.
Figure 5. R-curve based on the collected data from the calibration lab. Each color represents a different test subject.
Maxim’s algorithm outputs the R values. No further effort is required to obtain R from the recorded PPGs. After obtaining the R values with the corresponding reference SpO2 values, it is easy to obtain the calibration coefficients.
Data Collection Protocol
Figure 6. Data collection setup in the calibration lab.
Figure 7. Maxim's sensor placed in a wrist watch. The finger clips of two reference devices are attached to the index and middle fingers of the test subject
Derivation of SpO2 Calibration Coefficients from Collected Data
Figure 8. Reference SpO2 values and output R values.
Figure 9. The stable SpO2 plateaus are shown on the reference SpO2 values.
Figure 10. The stable SpO2 plateaus are shown on the reference SpO2 values and output R values.
Figure 11. Reference SpO2 values with respect to the calculated R values based on the collected data from the calibration lab before outlier elimination.
Figure 12. Reference SpO2 values with respect to the calculated R values based on the collected data from the calibration lab after outlier elimination.
Table 1: Default Calibration Coefficients
|Sensor||Default Calibration Coefficient Without The Optical Shield|
(only for a specific PD-LED separation
Leave-One-Out Cross-Validation of Algorithm Performance
Using SpO2 Calibration Coefficients Obtained from the Calibration Lab
When the three calibration coefficients are obtained, they need to be loaded to the MAX32664 through the I2C interface during the initialization process. For more information on the list of commands and initialization instructions, refer to the MAX32664 User Guide and the related application notes for each specific part.
 Sepponen, R. (2011). Development of a fractional multi-wavelength pulse oximetry algorithm (Doctoral dissertation, Aalto University).
 MAX32664 User Guide
 Application Note 6847 Guidelines for the Opto-Mechanical Integration of Heart Rate Monitors in Wearable Earbud Devices
 Application Note 6846 Guidelines for the Opto-Mechanical Integration of Heart-Rate Monitors in Wearable Wrist Devices
|MAX30101||High-Sensitivity Pulse Oximeter and Heart-Rate Sensor for Wearable Health||Samples|
|MAX30102||High-Sensitivity Pulse Oximeter and Heart-Rate Sensor for Wearable Health||Samples|
|MAX32664||Ultra-Low Power Biometric Sensor Hub||Samples|
|MAX86140||Best-in-Class Optical Pulse Oximeter and Heart-Rate Sensor for Wearable Health||Samples|
|MAX86141||Best-in-Class Optical Pulse Oximeter and Heart-Rate Sensor for Wearable Health||Samples|
|MAX86160||Integrated Heart-Rate Sensor for In-Ear Applications||Samples|
|MAXM86161||Single-Supply Integrated Optical Module for HR and SpO2 Measurement||Samples|
|MAXREFDES101||MAXREFDES101#: Health Sensor Platform 2.0|
|MAXREFDES220||MAXREFDES220#: Finger Heart Rate and Pulse Oximeter Smart Sensor with Digital Signal Processing|
|EE-Mail||Subscribe to EE-Mail and receive automatic notice of new documents in your areas of interest.|
|Download||Download, PDF Format (1.1MB)|
|© Mar 26, 2019, Maxim Integrated Products, Inc.|
APP 6845: Mar 26, 2019
APPLICATION NOTE 6845, AN6845, AN 6845, APP6845, Appnote6845, Appnote 6845