
Keywords: automotive antenna protector, phantom power, active antenna, active antenna power, active antennae power protector, phantom power antenna protector, automotive antenna, antenna regulator, remote radio antenna
Related Parts


Selecting External Components for an Automotive Remote Antenna Regulator and CurrentSense Amplifier

Abstract: This application note helps system designers choose the correct external components for use with the MAX16946 remote antenna regulator and currentsense amplifier (CSA), ensuring that automobile antennadetection subsystems meet their performance objectives. An electronic calculator is provided that helps specify the critical external components for the MAX16946. The calculator also determines the device's operational ranges and analog output voltage accuracy.
Introduction
The
MAX16946 is a highvoltage regulator with a precision currentsense amplifier (CSA), designed to provide phantom power to remote radio antennas in automotive applications. The device provides shortcircuit protection, currentlimit protection, and openload detection. The current levels for currentlimit protection and openload detection are programmable with external resistors. To ensure that antenna detection circuitry meets performance objectives, the design engineer must choose the correct external components for the design.
Figure 1 shows a typical application for the MAX16946. The main external components and their functions are as follows:
 R_{SENSE} is the resistor across which the load current is sensed. The CSA measures and amplifies the voltage across this resistor. For this reason, the value of the sense resistor is important in determining the overall system accuracy.
 R_{5} and R_{6} set the regulator output voltage.
 The capacitor at COMP ensures the stability of the regulator under all operating conditions.
 R_{1} and R_{2} set the current limit during a fault condition. If the current remains at current limit for a blanking time of 100ms (min), the output is turned off, the activelow SC output is asserted low, and a retry is attempted after 1100ms.
 R_{3} and R_{4} set the threshold for the openload detection. Below this load current, the activelow OL output asserts low.
 The Schottky diode D_{OUT} protects the MAX16946 from negative voltage transients on its OUT pin when the output is turned off and L_{OUT} attempts to maintain current flow. Without this diode, OUT might go below its absolute maximum voltage of 0.3V, which should not be allowed.
Figure 1. Typical operating circuit of the MAX16946 remote antenna CSA and switch.
When working with CSAs and switches for antenna applications, the designer must often determine the ranges for open load, normal operation, short circuit, and current limiting (Figure 2). In addition, the accuracy of the CSA's analog output voltage must be verified.
Figure 2. Operation ranges for the currentsense amplifiers.
Use the
MAX16946 Calculator to determine the correct values for the sense resistor and the resistive dividers, which set the currentlimit and the openload thresholds. It takes into account the tolerances of both the external components and the MAX16946. By calculating the tolerance ranges for each of the design parameters, the designer ensures that the design parameters are within the limits imposed by the system specification.
Calculating the Sense Resistor Value
Ideally, the maximum load current develops the fullscale sense voltage across the currentsense resistor, R_{SENSE} (Figure 1). The upper limit is represented by the shortcircuit current threshold of 1.7V compared to AOUT. The maximum load current in the application should never exceed the shortcircuit current threshold, otherwise a shortcircuit will be erroneously indicated. Calculate an initial value for R_{SENSE} using:

(Eq. 1) 
Where 1.7V is the shortcircuit current threshold, 0.4V is the zerocurrent offset of AOUT, 26V/V is the gain of the currentsense amplifier, and I_{SC} is the shortcircuit threshold.
Because the sense resistor has some tolerance, the nominal value needed will be lower than the value calculated in Equation 1. To calculate for the tolerance:

(Eq. 2) 
Where R_{SENSE} is the value of the sense resistor calculated in Equation 1, and R_{SENSETOLERANCE} is the tolerance of the sense resistor.
Normally one would choose the closest smaller standard value for R_{SENSE(NOM)}. Alternatively, serial or parallel combinations of standard resistors can be used to attain the optimal value for the sense resistor.
Calculating the ShortCircuit CurrentDetection Range
After choosing the nominal value of the sense resistor, next the typical current through the sense resistor needs to be determined. This current, which allows a short circuit to be detected, can be calculated as follows:

(Eq. 3) 
Where R_{SENSE(NOM)} is the sense resistor selected above.
However, since the shortcircuit current threshold (1.7V), the CSA gain (26V/V), and the AOUT zerocurrent offset voltage (0.4V) have uncorrelated tolerances (i.e., have minimum and maximum values that vary independently of each other), the value of I_{SC} will vary within a certain range. The limits of this range are:

(Eq. 4) 
And

(Eq. 5) 
Where R_{SENSE(MAX)} is the maximum value of the sense resistor (including its tolerance) and R_{SENSE(MIN)} is its minimum value. The activelow shortcircuit flag (SC) will thus assert low when the current falls between I_{SC(MIN)} and I_{SC(MAX)}.
Setting the Output Voltage
The resistors R_{5} and R_{6} in Figure 1 set the output voltage of the MAX16946. The equation governing their values is:

(Eq. 6) 
Where V_{FB} is the voltage at the feedback pin in regulation (1V nominal). The minimum and maximum values of the output voltage are then:

(Eq. 7) 
And

(Eq. 8) 
Where V_{FB(MIN)} is 0.97V and V_{FB(MAX)} is 1.03V (over the current range of 5mA to 150mA). R_{5(MAX)}, R_{5(MIN)}, R_{6(MAX)}, and R_{6(MIN)} are the maximum and minimum values of R_{5} and R_{6}, respectively.
Note that the output voltage can be set to 8.5V by connecting the FB pin to REG. In this mode, higher output voltage accuracy is achieved because the tolerance of external resistors does not need to be taken into account.
Setting the CurrentLimit Range
The MAX16946 limits its output current when the AOUT voltage reaches the voltage on the LIM pin, which is set using a resistordivider between REF, LIM, and GND. The nominal REF voltage is 3V. Thus, the following equation applies:

(Eq. 9) 
Where I_{LIM} is the desired currentlimit threshold. Choose the standard value of 100kΩ for R_{1}. R_{2} can then be calculated:

(Eq. 10) 
Considering uncorrelated tolerances, the worstcase currentlimit range is:

(Eq. 11) 
And

(Eq. 12) 
Where R_{1(MAX)}, R_{1(MIN)}, R_{2(MAX)}, and R_{2(MIN)} are the maximum and minimum values of R_{1} and R_{2}, respectively.
Setting the OpenLoad Detection Threshold
The openload threshold for the MAX16946 can be adjusted externally with a resistordivider placed between REF, OLT, and GND. The following equation applies:

(Eq. 13) 
Where I_{OL} is the desired openload threshold. Choose the standard value of 100kΩ for R_{3}. R_{4} can then be calculated:

(Eq. 14) 
After defining the values of R_{3} and R_{4}, the following equations can calculate the range of the openload detection threshold:

(Eq. 15) 
And

(Eq. 16) 
Where R_{3(MAX)}, R_{3(MIN)}, R_{4(MAX)}, and R_{4(MIN)} are the maximum and minimum values of R_{3} and R_{4}, respectively.
Measuring the Output Current by Means of the AOUT Voltage
With a given sense resistor, R_{SENSE}, and a defined load current, I_{LOAD}, the worstcase range of voltage values measured at the CSA's output, AOUT, can now be calculated. The general expression for the voltage on AOUT is:

(Eq. 17) 
If we again take into consideration all uncorrelated tolerances, the AOUT voltage will lie between the following equations:

(Eq. 18) 
And

(Eq. 19) 
In other words, the sensed current produces a worstcase AOUT voltage variation between V_{AOUT(MIN)} and V_{AOUT(MAX)}.
Normally the AOUT voltage is measured using the ADC of a microcontroller and the load current is then calculated based on the nominal values of all parameters. With the above worstcase AOUT voltages, the microcontroller would then conclude that the current is within range of the following two values:

(Eq. 20) 
And

(Eq. 21) 
The tolerance of the current measurement made by the ADC, I_{TOL}, is:

(Eq. 22) 
A Sample Calculation
For the following example, we assume an antenna phantom supply application where the upper end of the normal operation range is set at 100mA and the antenna requires a regulated voltage of 5V. If we set the shortcircuit threshold 10% higher at 110mA, then the initial value of the sense resistor is:

(Eq. 23) 
When using a resistor with a 1% tolerance, the maximum nominal value of the sense resistor is:

(Eq. 24) 
If the nextlowest E12 series value of 0.39Ω is selected, the typical value for shortcircuit detection with this resistor can be calculated:

(Eq. 25) 
ShortCircuit Threshold
The minimum and maximum values of the shortcircuit detection threshold can then be determined using the minimum and maximum values of the sense resistor (0.386Ω and 0.394Ω, assuming a 1% type is used):

(Eq. 26) 
And

(Eq. 27) 
Output Voltage
The output voltage of 5V is set by selecting resistor R_{6} (after first selecting a value of 22kΩ for R_{5}) according to the following equation:

(Eq. 28) 
If the nearest E12 series resistor of 5600Ω is selected, the nominal output voltage will be 4.93V and the variation of the output voltage will be between:

(Eq. 29) 
And

(Eq. 30) 
Current Limit
Next, the resistors can be selected to set the output current limit. Assuming a current limit of approximately 200mA, use a 100kΩ resistor for R_{1}:

(Eq. 31) 
Choosing the nearest E12 standard value of 390kΩ gives an actual current limit of 0.196A. Considering all tolerances and assuming 1% resistors are used, the minimum and maximum values for the currentlimit range are:

(Eq. 32) 
And

(Eq. 33) 
OpenLoad Detection Threshold
To set a nominal openload detection current of 10mA, select R_{4} using the following equation (having first selected a value of 100kΩ for R_{3}):

(Eq. 34) 
Using a standard resistor for R_{4} of 20kΩ, calculate the minimum and maximum values of the openload threshold:

(Eq. 35) 
And

(Eq. 36) 
AOUT Accuracy
To evaluate the analog output (AOUT) accuracy, we assume the same sense resistor selected above (0.39Ω) and evaluate the accuracy at a load current of 100mA. At this current, the minimum and maximum values of the AOUT voltage are:

(Eq. 37) 
And

(Eq. 38) 
Taking these voltages and using the microcontroller's software to calculate these voltages back to current (i.e., using the typical values from the data sheet), a range of an evaluated current can be derived between:

(Eq. 39) 
And

(Eq. 40) 
Thus, the range of error in the measurement made by the microcontroller is ±6.7% at 100mA. This range does not take into account other errors in the ADC measurement such as reference error, quantization error, etc.
Related Parts 
MAX16946 
Remote Antenna, CurrentSense and LDO/Switches 
Samples

MAX16947 
Remote Antenna, CurrentSense and LDO/Switches 

© Feb 03, 2012, Maxim Integrated Products, Inc.

The content on this webpage is protected by copyright laws of the United States and of foreign countries. For requests to copy this content, contact us.
APP 5272: Feb 03, 2012
APPLICATION NOTE 5272,
AN5272,
AN 5272,
APP5272,
Appnote5272,
Appnote 5272
