回到顶部
产品详情
Parametric specs for Supervisors (2 Monitored Voltages)
Reset Thresh. (V) | 2.5 to 3.3 3.3 to 5.5 |
Reset Thresh. Accur. (%) (@ +25°C) | 2.5 |
Interface | Factory Fixed |
tRESET (min) | 85ms to 300ms |
Watchdog Feature | No Watchdog |
Supervisor Features | Manual Reset Power Fail Comparator/Low Battery Detect |
ICC (µA) (max) | 50 |
Package/Pins | See Data Sheet |
缩小
简化框图
Technical Docs
数据资料 | 双路、经济型复位芯片,带有手动复位按钮 | Jul 17, 2000 |
支持和培训
采样:
选择上方“样片”按钮将重定向至第三方ADI样片网站。登录后,所选部件将转移到您在此网站上的购物车。如果您之前从未使用过此网站,请创建一个新帐户。有关此样片网站的任何问题,请联系SampleSupport@analog.com。
参量
Parametric specs for Supervisors (2 Monitored Voltages)
Reset Thresh. (V) | 2.5 to 3.3 3.3 to 5.5 |
Reset Thresh. Accur. (%) (@ +25°C) | 2.5 |
Interface | Factory Fixed |
tRESET (min) | 85ms to 300ms |
Watchdog Feature | No Watchdog |
Supervisor Features | Manual Reset Power Fail Comparator/Low Battery Detect |
ICC (µA) (max) | 50 |
Package/Pins | See Data Sheet |
主要特征
- Monitors both 3.3V and 5V power supplies
- 3.3V and 5V power-on and power transient resets
- Provides pushbutton switch for manual reset control
- Active low push-pull outputs (DS1834)
- Active low open-drain outputs (DS1834A)
- Active high push-pull outputs (DS1834D)
- Draws internal power from the higher of the two sources
- Uses precision temperature-compensated voltage reference and sensor
- Maintains active high reset for 350ms after power return
- Internal 5kΩ pull-up resistor
- Operating ranges:
- 5V with 5% or 10% tolerance
- 3.3V with 10% or 20% tolerance
- -40°C to +85°C
应用/用途
描述
The DS1834 Dual EconoReset with Pushbutton is designed to monitor power and protect processing in dual-voltage systems. It operates from the higher of a 3-volt or 5-volt input, monitoring both for in-tolerance conditions. When safety thresholds are breached from either input, the DS1834 initiates reset. On power return, it automatically restarts the processor, maintaining reset for 350ms to allow stabilization. The DS1834 also monitors a pushbutton input to allow for external over-ride.
Using pin adjustments, voltage reset tolerances can be set in different combinations for the 5V and 3.V power supplies, respectively: 10% and 10% 10% and 20% and 5% and 10%. DS1834A NMOS outputs can be wire-AND'd to either the 5-volt or 3-volt level. The DS1834 and DS1834D have CMOS outputs for low-current operation.
The DS1834 is targeted for multi-voltage microprocessor systems and subsystems, or for buses that do not operate at the same voltage as the µP or core logic. By integrating monitoring functions required for a particular application, the DS1834 enhances processor reliability with considerable savings in space and cost.
Using pin adjustments, voltage reset tolerances can be set in different combinations for the 5V and 3.V power supplies, respectively: 10% and 10% 10% and 20% and 5% and 10%. DS1834A NMOS outputs can be wire-AND'd to either the 5-volt or 3-volt level. The DS1834 and DS1834D have CMOS outputs for low-current operation.
The DS1834 is targeted for multi-voltage microprocessor systems and subsystems, or for buses that do not operate at the same voltage as the µP or core logic. By integrating monitoring functions required for a particular application, the DS1834 enhances processor reliability with considerable savings in space and cost.
Technical Docs
数据资料 | 双路、经济型复位芯片,带有手动复位按钮 | Jul 17, 2000 |
支持和培训
采样:
选择上方“样片”按钮将重定向至第三方ADI样片网站。登录后,所选部件将转移到您在此网站上的购物车。如果您之前从未使用过此网站,请创建一个新帐户。有关此样片网站的任何问题,请联系SampleSupport@analog.com。