回到顶部

双路、经济型复位芯片,带有手动复位按钮

产品详情

主要特征

Parametric specs for Supervisors (2 Monitored Voltages)
Reset Thresh. (V) 2.5 to 3.3
3.3 to 5.5
Reset Thresh. Accur. (%) (@ +25°C) 2.5
Reset Out Active Low
Open Drain
Interface Factory Fixed
tRESET (min) 85ms to 300ms
Watchdog Feature No Watchdog
Supervisor Features Manual Reset
Power Fail Comparator/Low Battery Detect
ICC (µA) (max) 50
Package/Pins See Data Sheet
缩小

简化框图

Technical Docs

支持和培训

在Maxim的知识库中搜索技术问题的答案

过滤搜索

Maxim的专业工程师团队也会为您解答相应的技术问题,请访问Maxim的 支持中心

参量

Parametric specs for Supervisors (2 Monitored Voltages)
Reset Thresh. (V) 2.5 to 3.3
3.3 to 5.5
Reset Thresh. Accur. (%) (@ +25°C) 2.5
Reset Out Active Low
Open Drain
Interface Factory Fixed
tRESET (min) 85ms to 300ms
Watchdog Feature No Watchdog
Supervisor Features Manual Reset
Power Fail Comparator/Low Battery Detect
ICC (µA) (max) 50
Package/Pins See Data Sheet

主要特征

  • Monitors both 3.3V and 5V power supplies
  • 3.3V and 5V power-on and power transient resets
  • Provides pushbutton switch for manual reset control
  • Active low push-pull outputs (DS1834)
  • Active low open-drain outputs (DS1834A)
  • Active high push-pull outputs (DS1834D)
  • Draws internal power from the higher of the two sources
  • Uses precision temperature-compensated voltage reference and sensor
  • Maintains active high reset for 350ms after power return
  • Internal 5kΩ pull-up resistor
  • Operating ranges:
    • 5V with 5% or 10% tolerance
    • 3.3V with 10% or 20% tolerance
    • -40°C to +85°C

应用/用途

描述

The DS1834 Dual EconoReset with Pushbutton is designed to monitor power and protect processing in dual-voltage systems. It operates from the higher of a 3-volt or 5-volt input, monitoring both for in-tolerance conditions. When safety thresholds are breached from either input, the DS1834 initiates reset. On power return, it automatically restarts the processor, maintaining reset for 350ms to allow stabilization. The DS1834 also monitors a pushbutton input to allow for external over-ride.

Using pin adjustments, voltage reset tolerances can be set in different combinations for the 5V and 3.V power supplies, respectively: 10% and 10% 10% and 20% and 5% and 10%. DS1834A NMOS outputs can be wire-AND'd to either the 5-volt or 3-volt level. The DS1834 and DS1834D have CMOS outputs for low-current operation.

The DS1834 is targeted for multi-voltage microprocessor systems and subsystems, or for buses that do not operate at the same voltage as the µP or core logic. By integrating monitoring functions required for a particular application, the DS1834 enhances processor reliability with considerable savings in space and cost.

简化框图

DS1834、DS1834A、DS1834D:原理框图 DS1834、DS1834A、DS1834D:原理框图 Zoom icon

Technical Docs

支持和培训

在Maxim的知识库中搜索技术问题的答案

过滤搜索

Maxim的专业工程师团队也会为您解答相应的技术问题,请访问Maxim的 支持中心