回到顶部
产品详情
主要特征
应用/用途
Parametric specs for Digital I/O
Digital Input/Output | Digital Output |
Interface Type | CMOS |
# Channels | 1 |
VSUPPLY (V) (min) | 9 |
VSUPPLY (V) (max) | 70 |
ISUPPLY (µA) (typ) | 1.8 |
Oper. Temp. (°C) | -40 to +125 |
Package/Pins | TQFN/16 |
Budgetary Price (See Notes) | 1.99 |
缩小
简化框图
支持和培训
采样:
选择上方“样片”按钮将重定向至第三方ADI样片网站。登录后,所选部件将转移到您在此网站上的购物车。如果您之前从未使用过此网站,请创建一个新帐户。有关此样片网站的任何问题,请联系SampleSupport@analog.com。
参量
Parametric specs for Digital I/O
Digital Input/Output | Digital Output |
Interface Type | CMOS |
# Channels | 1 |
VSUPPLY (V) (min) | 9 |
VSUPPLY (V) (max) | 70 |
ISUPPLY (µA) (typ) | 1.8 |
Oper. Temp. (°C) | -40 to +125 |
Package/Pins | TQFN/16 |
Budgetary Price (See Notes) | 1.99 |
主要特征
- +9V to +70V Operating Supply Range
- 5V / 50mA Integrated Linear Regulator
- -40°C to +125°C Ambient Temperature Operating Range
- 16-TQFN Package, 3mm x 3mm, 0.5mm Pin Pitch
- Robust Design Features
- Ultra High-Speed Inductive Load Turn-Off by Clamping to -70V
- Supply Independent Inductive Clamping
- Support of Low RON FETs Having Qg (Total) = 50nC
- External FET Turn-On Propagation Delay < 20μs
- Active Current Limit Control During Overcurrent
- Fault Monitoring Diagnostic Features
- Overcurrent Detect Output
- High Supply-Voltage Indication
- Flexible Supply or Load Voltage Monitor
- Undervoltage Lockout
- Thermal Warning and Shutdown Protection
- Device Ready Indication
应用/用途
- Industrial Digital Outputs
- High-Side Switches
- Motor Holding Brakes
- Relay and Solenoid Drivers
描述
The MAX14922 is a high-side, n-channel FET controller for implementing industrial high-side switches for switching ground-connected loads. The MAX14922 device controls an external nMOS power transistor, allowing low RON high-side switch applications from a +9V to +70V supply range. Fast inductive load turn-off can be achieved with use of a high-voltage TVS diode enabling up to -70V (max) voltage clamping. Ground-connected TVS diodes allow clamping of exceptionally high inductive energies. Load current is limited to a user-defined value through a sense resistor. External FET overload protection is achieved using an auto-retry timing feature, as defined by a user-selected capacitor (CBLANK at tBLANK input) or optionally using an external timing control. The MAX14922 features an on-chip comparator enabling monitoring of the high-side switch output or the supply input voltage with a user-selected threshold. An integrated charge pump enables high speed switching rates when using low RON FETs in the 20kHz to 50kHz range. The MAX14922 is available in a 3mm x 3mm, 16-TQFN package. The MAX14922 device is specified over the -40°C to +125°C operating temperature range.
支持和培训
采样:
选择上方“样片”按钮将重定向至第三方ADI样片网站。登录后,所选部件将转移到您在此网站上的购物车。如果您之前从未使用过此网站,请创建一个新帐户。有关此样片网站的任何问题,请联系SampleSupport@analog.com。