回到顶部
MyMaxim 订阅产品详情
主要特征
应用/用途
Parametric specs for Battery Chargers
| Charging VIN (V) (max) | 6.5 |
| Max. ICHG (A) | 0.5 |
| Cell Chemistry | Li-Ion Li-Polymer |
| # Lithium Ion Cells | 1 |
| Protected VIN (V) (max) | 6.5 |
| Charger (V) | 4.1 4.2 |
| Oper. Temp. (°C) | -40 to +85 |
| Package/Pins | SOIC (N)/8 |
| Budgetary Price (See Notes) | 2.04 |
缩小
简化框图
Technical Docs
支持和培训
采样:
选择上方“样片”按钮将重定向至第三方ADI样片网站。登录后，所选部件将转移到您在此网站上的购物车。如果您之前从未使用过此网站，请创建一个新帐户。有关此样片网站的任何问题，请联系SampleSupport@analog.com。
参量
Parametric specs for Battery Chargers
| Charging VIN (V) (max) | 6.5 |
| Max. ICHG (A) | 0.5 |
| Cell Chemistry | Li-Ion Li-Polymer |
| # Lithium Ion Cells | 1 |
| Protected VIN (V) (max) | 6.5 |
| Charger (V) | 4.1 4.2 |
| Oper. Temp. (°C) | -40 to +85 |
| Package/Pins | SOIC (N)/8 |
| Budgetary Price (See Notes) | 2.04 |
主要特征
- Charges Single-Cell Li+ Batteries Directly from USB Port
- 0.5% Overall Charging Accuracy
- Minimal External Components
- Input Diode Not Required
- Automatic IC Thermal Regulation
- Preconditions Near-Depleted Cells
- Convenient Power SO-8 Package (1.4W)
应用/用途
- 蜂窝电话
- 数码相机
- 手持式计算机
- MP3播放器
- PDA与掌上电脑
- 双向寻呼
描述
The MAX1811 is a single-cell lithium-ion (Li+) battery charger that can be powered directly from a USB port or from an external supply up to 6.5V. It has a 0.5% overall battery regulation voltage accuracy to allow maximum utilization of the battery capacity.
The charger uses an internal FET to deliver up to 500mA charging current to the battery. The device can be configured for either a 4.1V or 4.2V battery, using the SELV input. The SELI input sets the charge current to either 100mA or 500mA. An open-drain output (active-low CHG) indicates charge status.
The MAX1811 has preconditioning that soft-starts a near-dead battery cell before charging. Other safety features include continuous monitoring of voltage and current and initial checking for fault conditions before charging.
The MAX1811 is available in a small 1.4W thermally enhanced 8-pin SO package.
The charger uses an internal FET to deliver up to 500mA charging current to the battery. The device can be configured for either a 4.1V or 4.2V battery, using the SELV input. The SELI input sets the charge current to either 100mA or 500mA. An open-drain output (active-low CHG) indicates charge status.
The MAX1811 has preconditioning that soft-starts a near-dead battery cell before charging. Other safety features include continuous monitoring of voltage and current and initial checking for fault conditions before charging.
The MAX1811 is available in a small 1.4W thermally enhanced 8-pin SO package.
Technical Docs
支持和培训
采样:
选择上方“样片”按钮将重定向至第三方ADI样片网站。登录后，所选部件将转移到您在此网站上的购物车。如果您之前从未使用过此网站，请创建一个新帐户。有关此样片网站的任何问题，请联系SampleSupport@analog.com。
询价申请