产品详情
The MAX17320 is a 38µA IQ stand-alone pack-side fuel gauge IC with protector, battery internal self-discharge detection, and optional SHA-256 authentication for 2 to 4 series lithium-ion/polymer batteries.
The IC monitors the voltage, current, temperature and state of the battery to provide protection against over/undervoltage, overcurrent, short-circuit, over/undertemperature, overcharge, and internal self-discharge conditions using external high-side N-FETs, and provides charging prescription to ensure that the battery operates under safe conditions, thereby prolonging the life of the battery. The IC balances the cells using internal FETs. During prequal charging, the IC uses the CHGFET to linearly control charging.
To prevent battery pack cloning, the IC integrates SHA-256 authentication with a 160-bit secret key. Each IC incorporates a unique 64-bit ID.
The fuel gauge uses Maxim ModelGauge™ m5 algorithm that combines the short-term accuracy and linearity of a coulomb counter with the long-term stability of a voltage-based fuel gauge to provide industry-leading fuel gauge accuracy. The IC automatically compensates for cell aging, temperature, and discharge rate, and provides accurate state-of-charge (SOC) in milliampere-hours (mAh) or percentage (%) over a wide range of operating conditions.
The IC provides a configurable always-on LDO that can power small critical loads on the system side without overloading the cells even under fault conditions. Dynamic power functionality provides the instantaneous maximum battery output power which can be delivered to the system without violating the minimum system input voltage.
A Maxim 1-Wire® or 2-wire I2C/SMBus interface provides access to data and control registers. The IC is available in a lead-free, 2.4mm x 2.6mm 30-bump 0.4mm pitch WLP and 4mm x 4mm 24-pin TQFN packages.
主要特征
- Battery Health + Programmable Safety/Protection
- Overvoltage (Temperature Dependent)
- Overcharge/Overdischarge/Short-Circuit Current
- Over/Undertemperature
- Undervoltage + SmartEmpty
- Battery Internal Self-Discharge Detection
- Ideal Diode Discharge During Charge Fault
- Charging Prescriptions (JEITA)
- Prequal Charge Control with CHG FET
- ModelGauge m5 EZ Algorithm
- Percent, Capacity, Time-to-Empty/Full, Age
- Cycle+™ Age Forecast
- Precision Measurement Without Calibration
- Current, Voltage, Power, Time, Cycles
- Die Temperature, 4 Thermistors ±1°C
- Cell Balancing with Internal FETs
- SHA-256 Authentication
- Nonvolatile Memory for Stand-Alone Operation
- History Logging, User Data (84 Bytes)
- Low Quiescent Current
- FETs Enabled: 38µA Active
- Pushbutton Wakeup—Eliminates System Consumption Until Button Press
- Always-On LDO
- Dynamic Power—Estimates Power Capability
- SBS 1.1 Compatible Register Set
应用/用途
- 数码相机、视频和运动摄像机
- null
- 医疗设备、健康和健身监测仪
- null
- null
- 智能电话、平板电脑、二合一笔记本电脑
Functions | Battery ID Fuel Gauge SHA-256 Authentication |
Interface | 1-Wire 2-Wire |
User Data Storage (bits) | 672 NVM |
VSUPPLY (V) | 4.2 to 18 |
Package/Pins | TQFN-CU/24 WLP/30 |
Oper. Temp. (°C) | -40 to +85 |
Budgetary Price (See Notes) | $1.55 @1k |
Functions | Fuel Gauge Protector |
Battery Type | 2-4 Cell Li-Ion |
Fuel Gauge Algorithm | ModelGauge m5 |
Interface | 1-Wire 2-Wire |
User Data Storage (Bytes) | 84 NVM |
Parameters Measured | Current State of Charge Temperature Time Voltage |
Applications | Pack |
Battery Protection Features | 2-Level Charger-Communication Timeout Internal Self-Discharge Over Voltage Over-Charge Over-Current Over-Temperature Over/Under Voltage |
VSUPPLY (V) (min) | 4.2 |
VSUPPLY (V) (max) | 18 |
Package/Pins | TQFN-CU/24 WLP/30 |
Oper. Temp. (°C) | -40 to +85 |
Budgetary Price (See Notes) | $1.55 @1k |
单击下面的标题以查看详情页面
描述
The MAX17320X/MAX17320G evaluation kits (EV kits) are fully assembled and tested surface-mount PCBs that evaluate the stand-alone pack-side fuel gauge IC with protector and optional SHA-256 authentication for 2-4 cell lithium-ion/polymer batteries.
The MAX17320 EV kits include the IC evaluation board with integrated I2C/1-Wire® interface and USB micro-B cable. Windows® based graphical user interface (GUI) software is available for use with the EV kit and can be downloaded from https:// www.maximintegrated.com/products/MAX17320.html/ product page under “Design Resources” tab. Windows 7 or newer Windows operating system is required to use with the EV kit GUI software.
查看详情特征
- ModelGauge m5 Algorithm
- Monitors Multicell Packs
- Full Protection Solution On-Board for Evaluation
- Battery Pack Input Voltage Range of +2.3V to +4.9V/Cell with Default Hardware
- Default Current Range -10A to +10A with 5mΩ Sense Resistor, Higher Currents Can Be Supported by Changing to a Smaller Sense Resistor
- Thermistor Measurement
- On-Board I2C/1-Wire Communication Interface with Built-In MAXUSB Interface
- Windows 7 or Newer Compatible Software
- Proven PCB Layout
- Fully Assembled and Tested
描述
The MAX17320X/MAX17320G evaluation kits (EV kits) are fully assembled and tested surface-mount PCBs that evaluate the stand-alone pack-side fuel gauge IC with protector and optional SHA-256 authentication for 2-4 cell lithium-ion/polymer batteries.
The MAX17320 EV kits include the IC evaluation board with integrated I2C/1-Wire® interface and USB micro-B cable. Windows® based graphical user interface (GUI) software is available for use with the EV kit and can be downloaded from https:// www.maximintegrated.com/products/MAX17320.html/ product page under “Design Resources” tab. Windows 7 or newer Windows operating system is required to use with the EV kit GUI software.
查看详情特征
- ModelGauge m5 Algorithm
- Monitors Multicell Packs
- Full Protection Solution On-Board for Evaluation
- Battery Pack Input Voltage Range of +2.3V to +4.9V/Cell with Default Hardware
- Default Current Range -10A to +10A with 5mΩ Sense Resistor, Higher Currents Can Be Supported by Changing to a Smaller Sense Resistor
- Thermistor Measurement
- On-Board I2C/1-Wire Communication Interface with Built-In MAXUSB Interface
- Windows 7 or Newer Compatible Software
- Proven PCB Layout
- Fully Assembled and Tested
描述
The MAX17320X/MAX17320G evaluation kits (EV kits) are fully assembled and tested surface-mount PCBs that evaluate the stand-alone pack-side fuel gauge IC with protector and optional SHA-256 authentication for 2-4 cell lithium-ion/polymer batteries.
The MAX17320 EV kits include the IC evaluation board with integrated I2C/1-Wire® interface and USB micro-B cable. Windows® based graphical user interface (GUI) software is available for use with the EV kit and can be downloaded from https:// www.maximintegrated.com/products/MAX17320.html/ product page under “Design Resources” tab. Windows 7 or newer Windows operating system is required to use with the EV kit GUI software.
查看详情特征
- ModelGauge m5 Algorithm
- Monitors Multicell Packs
- Full Protection Solution On-Board for Evaluation
- Battery Pack Input Voltage Range of +2.3V to +4.9V/Cell with Default Hardware
- Default Current Range -10A to +10A with 5mΩ Sense Resistor, Higher Currents Can Be Supported by Changing to a Smaller Sense Resistor
- Thermistor Measurement
- On-Board I2C/1-Wire Communication Interface with Built-In MAXUSB Interface
- Windows 7 or Newer Compatible Software
- Proven PCB Layout
- Fully Assembled and Tested
描述
The MAX17320X/MAX17320G evaluation kits (EV kits) are fully assembled and tested surface-mount PCBs that evaluate the stand-alone pack-side fuel gauge IC with protector and optional SHA-256 authentication for 2-4 cell lithium-ion/polymer batteries.
The MAX17320 EV kits include the IC evaluation board with integrated I2C/1-Wire® interface and USB micro-B cable. Windows® based graphical user interface (GUI) software is available for use with the EV kit and can be downloaded from https:// www.maximintegrated.com/products/MAX17320.html/ product page under “Design Resources” tab. Windows 7 or newer Windows operating system is required to use with the EV kit GUI software.
查看详情特征
- ModelGauge m5 Algorithm
- Monitors Multicell Packs
- Full Protection Solution On-Board for Evaluation
- Battery Pack Input Voltage Range of +2.3V to +4.9V/Cell with Default Hardware
- Default Current Range -10A to +10A with 5mΩ Sense Resistor, Higher Currents Can Be Supported by Changing to a Smaller Sense Resistor
- Thermistor Measurement
- On-Board I2C/1-Wire Communication Interface with Built-In MAXUSB Interface
- Windows 7 or Newer Compatible Software
- Proven PCB Layout
- Fully Assembled and Tested
参量
Functions | Battery ID Fuel Gauge SHA-256 Authentication |
Interface | 1-Wire 2-Wire |
User Data Storage (bits) | 672 NVM |
VSUPPLY (V) | 4.2 to 18 |
Package/Pins | TQFN-CU/24 WLP/30 |
Oper. Temp. (°C) | -40 to +85 |
Budgetary Price (See Notes) | $1.55 @1k |
Functions | Fuel Gauge Protector |
Battery Type | 2-4 Cell Li-Ion |
Fuel Gauge Algorithm | ModelGauge m5 |
Interface | 1-Wire 2-Wire |
User Data Storage (Bytes) | 84 NVM |
Parameters Measured | Current State of Charge Temperature Time Voltage |
Applications | Pack |
Battery Protection Features | 2-Level Charger-Communication Timeout Internal Self-Discharge Over Voltage Over-Charge Over-Current Over-Temperature Over/Under Voltage |
VSUPPLY (V) (min) | 4.2 |
VSUPPLY (V) (max) | 18 |
Package/Pins | TQFN-CU/24 WLP/30 |
Oper. Temp. (°C) | -40 to +85 |
Budgetary Price (See Notes) | $1.55 @1k |
主要特征
- Battery Health + Programmable Safety/Protection
- Overvoltage (Temperature Dependent)
- Overcharge/Overdischarge/Short-Circuit Current
- Over/Undertemperature
- Undervoltage + SmartEmpty
- Battery Internal Self-Discharge Detection
- Ideal Diode Discharge During Charge Fault
- Charging Prescriptions (JEITA)
- Prequal Charge Control with CHG FET
- ModelGauge m5 EZ Algorithm
- Percent, Capacity, Time-to-Empty/Full, Age
- Cycle+™ Age Forecast
- Precision Measurement Without Calibration
- Current, Voltage, Power, Time, Cycles
- Die Temperature, 4 Thermistors ±1°C
- Cell Balancing with Internal FETs
- SHA-256 Authentication
- Nonvolatile Memory for Stand-Alone Operation
- History Logging, User Data (84 Bytes)
- Low Quiescent Current
- FETs Enabled: 38µA Active
- Pushbutton Wakeup—Eliminates System Consumption Until Button Press
- Always-On LDO
- Dynamic Power—Estimates Power Capability
- SBS 1.1 Compatible Register Set
应用/用途
- 数码相机、视频和运动摄像机
- null
- 医疗设备、健康和健身监测仪
- null
- null
- 智能电话、平板电脑、二合一笔记本电脑
描述
The MAX17320 is a 38µA IQ stand-alone pack-side fuel gauge IC with protector, battery internal self-discharge detection, and optional SHA-256 authentication for 2 to 4 series lithium-ion/polymer batteries.
The IC monitors the voltage, current, temperature and state of the battery to provide protection against over/undervoltage, overcurrent, short-circuit, over/undertemperature, overcharge, and internal self-discharge conditions using external high-side N-FETs, and provides charging prescription to ensure that the battery operates under safe conditions, thereby prolonging the life of the battery. The IC balances the cells using internal FETs. During prequal charging, the IC uses the CHGFET to linearly control charging.
To prevent battery pack cloning, the IC integrates SHA-256 authentication with a 160-bit secret key. Each IC incorporates a unique 64-bit ID.
The fuel gauge uses Maxim ModelGauge™ m5 algorithm that combines the short-term accuracy and linearity of a coulomb counter with the long-term stability of a voltage-based fuel gauge to provide industry-leading fuel gauge accuracy. The IC automatically compensates for cell aging, temperature, and discharge rate, and provides accurate state-of-charge (SOC) in milliampere-hours (mAh) or percentage (%) over a wide range of operating conditions.
The IC provides a configurable always-on LDO that can power small critical loads on the system side without overloading the cells even under fault conditions. Dynamic power functionality provides the instantaneous maximum battery output power which can be delivered to the system without violating the minimum system input voltage.
A Maxim 1-Wire® or 2-wire I2C/SMBus interface provides access to data and control registers. The IC is available in a lead-free, 2.4mm x 2.6mm 30-bump 0.4mm pitch WLP and 4mm x 4mm 24-pin TQFN packages.