回到顶部

Automotive 100W USB-PD Buck-Boost Port Controller and Protector

Industry's First Single-IC 100W Automotive USB-PD Power, Charger and Protector

产品详情

The MAX25430 combines an automotive-grade buck-boost controller capable of driving up to 5.0A, a USB-PD Analog Front-End (AFE), Legacy USB Charging support and USB Type-C™ protection for USB host or DFP applications. The USB Type-C protection switches provide automotive system-level ESD and 24V short-circuit protection for D+, D-, CC1, CC2, and VCONN. The device also supports legacy USB 2.0 charging modes including BC1.2, Apple° 2.4A, Apple CarPlay°, Apple MFi and USB On-The-Go (OTG).

The MAX25430B integrates a USB-PD AFE which supports the USB-IF Type-C Port Controller Interface (TCPCI) specification and can interface with any I2C Master in the application.

The MAX25430A provides CC signal passthrough protection for an external USB-PD controller.

G-Suffix devices include intelligent detection and protection to avoid high short-circuit currents flowing from the car battery through the cable shield to ground during fault events, preventing car module damage.

The MAX25430 EVKIT and collateral provides a convenient platform to the design engineer for rapid evaluation with reduced test and firmware development time. The MAX25430 is available in a small 6mm x 6mm 40-pin TQFN package and requires very few external components.

How to Quickly Set Up the MAX25430AEVKIT

主要特征

  • USB-PD PHY That is TCPCI Standard for Use with Any Low-Cost I2C Master Such as Hub IC, MCU or SOC (MAX25430B)
    • Ground-Offset-Adjusted BMC PHY for Maximum Signal-to-Noise Ratio
  • Non-TCPC Versions Available for Protecting External USB-PD Controller (MAX25430A)
  • Integrated Buck-Boost Controller for External H-bridge
    • 4.5V to 36V Input Operating Range
    • Fixed PDO 5V, 9V, 15V, and 20V up to 5.0A
    • 220kHz, 300kHz, or 400kHz Switching Frequency
    • External Frequency Synchronization and Spread Spectrum for Reduced EMI
  • Integrated and User-Programmable Buck-Boost Output Voltage Adjustment up to 500mΩ of Cable Resistance
  • Highest Performance, Safest, and Lowest Cost Passenger Cable-Shield Short-to-Battery Protection
    • Minimizes Short-Circuit Currents with a Small, Single-FET Solution
  • Integrated 3.0V to 5.5V 1W Smart, Reliable VCONN Switch with Protection
  • Integrated 24V Protection on HVD+, HVD-, HVCC1 and HVCC2
  • Integrated Legacy USB 2.0 Charging Support including BC1.2, Apple CarPlay, MFi R33, and OTG
  • Integrated ±15kV Air, ±8kV Contact ISO 10605 and IEC 61000-4-2 ESD Protection
  • -40°C to 125°C Operating Temperature Range
  • 40-Pin (6mm x 6mm) TQFN Package with EP
  • AEC-Q100 and AEC-Q006 Qualified
  • 应用/用途

    • null
    • null
    • null
    Parametric specs for USB Host Adapter Emulator
    Charging Modes Auto-CDP (Automatic Charging Downstream facing Port)
    Auto-DCP (Automatic Dedicated Charging Port)
    Default Firmware Update Mode
    First-Boot Factory Programming Mode
    High-Speed Pass-through
    USB Power Delivery (USB-PD) up to 100 W
    USB Type-C Downstream Facing Port (DFP)
    Supported Charging Configurations 1 Watt VCONN Support with protection and auto-fault handling
    Apple 1.0A, 2.1A, 2.4A, CarPlay, MFi R33
    CC Pin Protection for External USB-PD Controller
    Integrated Passenger Cable-Shield Short-To-Battery Protection
    Integrated USB-IF TCPC for External I2C Master
    Integrated high-voltage buck-boost controller
    USB-IF BC1.2; USB Type-C; USB-PD
    Supported USB Battery Charging Specification 1.2
    Current Limit Switch Control I2C
    CDP Emulation Yes
    Remote Wake-Up Support Yes
    VBUS Reset Time (sec) (typ) 0.016
    Package/Pins TQFN/40
    Oper. Temp. (°C) -40°C to +125°C
    Budgetary
    Price (See Notes)
    $2.56 @1k
    查看更多

    简化框图

    MAX25430: Simplified Block Diagram MAX25430: Simplified Block Diagram Zoom icon

    技术文档

    设计与质量

    单击下面的标题以查看详情页面

    描述

    The MAX25430 EVKIT and collateral provides a convenient platform to the design engineer for rapid evaluation with reduced test and firmware-development time.

    The MAX25430A evaluation kit (EV kit) demonstrates the MAX25430A automotive-grade buck-boost controller capable of driving up to 5.0A, Legacy USB Charging support and USB Type-C™ protection for USB host or DFP applications.

    The MAX25430A provides CC signal passthrough protection for the Cypress CCG3PA USB-PD controller.

    The integrated USB Type-C protection switches provide automotive system-level ESD and 24V short-circuit protection for D+, D-, CC1, CC2, and CC lines when used as VCONN supply. The device also supports legacy USB 2.0 charging modes including BC1.2, Apple® 2.4A, Apple CarPlay®, Apple MFi and USB On-The-Go (OTG).

    The register set can be reviewed using the Maxim Feather Board I2C to USB adapter, and the MAX2543x Graphical User Interface (GUI). Please contact the factory for more details.

    The MAX25430 offers a factory option that includes intelligent detection and protection to avoid high short-circuit currents flowing from the car battery through the cable shield to ground during fault events, preventing car module damage. To evaluate, refer to the Ordering Information table in the MAX25430 data sheet and order the G-suffix sample from the factory. Once received, replace on the EV Kit and unsolder the bypass short around MOSFET (Q6).

    How to Quickly Set Up the MAX25430AEVKIT

    查看详情

    特征

    • 100W USB-PD REV3.0 Source Charger Solution using a Cypress PD Controller
    • Legacy USB 2.0 Charging Support—Meets MFi R3x
    • Register Set Accessible with Feather Board and GUI
    • Test Points Available for Signal and Converter Analysis
    • EV Kit is Ready for Factory IC Option with Customer Cable Shield Short-to-Battery Protection
    • Proven PCB Layout
    • Fully Assembled and Tested

    /cn/design/design-tools/ee-sim.html?

    支持和培训

    在Maxim的知识库中搜索您所需的答案。

    过滤搜索

    Maxim专业的应用工程师团队也可以为您解答技术问题,请 访问Maxim的 支持中心

    参量

    Parametric specs for USB Host Adapter Emulator
    Charging Modes Auto-CDP (Automatic Charging Downstream facing Port)
    Auto-DCP (Automatic Dedicated Charging Port)
    Default Firmware Update Mode
    First-Boot Factory Programming Mode
    High-Speed Pass-through
    USB Power Delivery (USB-PD) up to 100 W
    USB Type-C Downstream Facing Port (DFP)
    Supported Charging Configurations 1 Watt VCONN Support with protection and auto-fault handling
    Apple 1.0A, 2.1A, 2.4A, CarPlay, MFi R33
    CC Pin Protection for External USB-PD Controller
    Integrated Passenger Cable-Shield Short-To-Battery Protection
    Integrated USB-IF TCPC for External I2C Master
    Integrated high-voltage buck-boost controller
    USB-IF BC1.2; USB Type-C; USB-PD
    Supported USB Battery Charging Specification 1.2
    Current Limit Switch Control I2C
    CDP Emulation Yes
    Remote Wake-Up Support Yes
    VBUS Reset Time (sec) (typ) 0.016
    Package/Pins TQFN/40
    Oper. Temp. (°C) -40°C to +125°C
    Budgetary
    Price (See Notes)
    $2.56 @1k

    主要特征

  • USB-PD PHY That is TCPCI Standard for Use with Any Low-Cost I2C Master Such as Hub IC, MCU or SOC (MAX25430B)
    • Ground-Offset-Adjusted BMC PHY for Maximum Signal-to-Noise Ratio
  • Non-TCPC Versions Available for Protecting External USB-PD Controller (MAX25430A)
  • Integrated Buck-Boost Controller for External H-bridge
    • 4.5V to 36V Input Operating Range
    • Fixed PDO 5V, 9V, 15V, and 20V up to 5.0A
    • 220kHz, 300kHz, or 400kHz Switching Frequency
    • External Frequency Synchronization and Spread Spectrum for Reduced EMI
  • Integrated and User-Programmable Buck-Boost Output Voltage Adjustment up to 500mΩ of Cable Resistance
  • Highest Performance, Safest, and Lowest Cost Passenger Cable-Shield Short-to-Battery Protection
    • Minimizes Short-Circuit Currents with a Small, Single-FET Solution
  • Integrated 3.0V to 5.5V 1W Smart, Reliable VCONN Switch with Protection
  • Integrated 24V Protection on HVD+, HVD-, HVCC1 and HVCC2
  • Integrated Legacy USB 2.0 Charging Support including BC1.2, Apple CarPlay, MFi R33, and OTG
  • Integrated ±15kV Air, ±8kV Contact ISO 10605 and IEC 61000-4-2 ESD Protection
  • -40°C to 125°C Operating Temperature Range
  • 40-Pin (6mm x 6mm) TQFN Package with EP
  • AEC-Q100 and AEC-Q006 Qualified
  • 应用/用途

    • null
    • null
    • null

    描述

    The MAX25430 combines an automotive-grade buck-boost controller capable of driving up to 5.0A, a USB-PD Analog Front-End (AFE), Legacy USB Charging support and USB Type-C™ protection for USB host or DFP applications. The USB Type-C protection switches provide automotive system-level ESD and 24V short-circuit protection for D+, D-, CC1, CC2, and VCONN. The device also supports legacy USB 2.0 charging modes including BC1.2, Apple° 2.4A, Apple CarPlay°, Apple MFi and USB On-The-Go (OTG).

    The MAX25430B integrates a USB-PD AFE which supports the USB-IF Type-C Port Controller Interface (TCPCI) specification and can interface with any I2C Master in the application.

    The MAX25430A provides CC signal passthrough protection for an external USB-PD controller.

    G-Suffix devices include intelligent detection and protection to avoid high short-circuit currents flowing from the car battery through the cable shield to ground during fault events, preventing car module damage.

    The MAX25430 EVKIT and collateral provides a convenient platform to the design engineer for rapid evaluation with reduced test and firmware development time. The MAX25430 is available in a small 6mm x 6mm 40-pin TQFN package and requires very few external components.

    How to Quickly Set Up the MAX25430AEVKIT

    简化框图

    MAX25430: Simplified Block Diagram MAX25430: Simplified Block Diagram Zoom icon

    技术文档

    支持和培训

    在Maxim的知识库中搜索您所需的答案。

    过滤搜索

    Maxim专业的应用工程师团队也可以为您解答技术问题,请 访问Maxim的 支持中心