产品详情
MAX4983E/MAX4984E双刀/双掷(DPDT)开关完全工作于+2.8V至+5.5V单电源,COM1和COM2具有+5.5V的短路保护。该特性使MAX4983E/MAX4984E完全符合USB 2.0规范中的VBUS故障保护要求。这些器件具有较低的逻辑门限电压输入,可用于具有低I/O电压的系统。MAX4983E具有低电平有效的使能输入(/EN),当该引脚为高电平时,器件进入关断模式。MAX4984E具有高电平有效的使能输入(EN),当该引脚为低电平时,器件进入关断模式。器件处于关断模式时,静态电源电流降低至0.1µA。
MAX4983E/MAX4984E采用节省空间的10引脚、1.4mm x 1.8mm、UTQFN封装,工作在-40°C至+85°C温度范围。
主要特征
- USB高速开关
- COM端具有ESD保护
- ±15kV人体模型
- ±15kV IEC 61000-4-2气隙放电
- ±8kV IEC 61000-4-2接触放电
- 工作电源范围:+2.8V至+5.5V
- 5Ω (典型值)的低导通电阻(RON)
- -3dB带宽:950MHz (典型值)
- 兼容低至1.4V的逻辑I/O
- COM模拟输入端具有+5.5V的短路故障保护
- 0.6µA (典型值)的低电源电流
- 使能输入:
- MAX4983E:低电平有效(/EN)
- MAX4984E:高电平有效(EN)
- 小尺寸、10引脚、1.4mm x 1.8mm UTQFN封装
应用/用途
- 总线切换
- 蜂窝电话
- 数码相机
- GPS
- 笔记本电脑
- PDA
- 视频开关
Protocol | USB Full-Speed USB High-Speed USB Low-Speed |
Configuration | 2-to-1 DPDT |
# Channels | 2 |
VSUPPLY (Single) (V) (min) | 2.8 |
VSUPPLY (Single) (V) (max) | 5.5 |
VSIGNAL (V) (min) | 0 |
VSIGNAL (V) (max) | 5.5 |
Dynamic Range (max) (V) (max) | 5.5 |
RON (Ω) (max) | 10 |
RFLAT(ON) (Ω) (typ) | 0.1 |
Package/Pins | ULTRA TQFN/10 |
Budgetary Price (See Notes) | $2.48 @1k |
技术文档
数据资料 | 高速USB 2.0开关,具有±15kV ESD保护 | Feb 26, 2010 |
单击下面的标题以查看详情页面
描述
MAX4983E评估板(EV kit)提供经过验证的设计,用于评估MAX4983具有较高ESD保护的双刀双掷(DPDT)开关。评估板为演示MAX4983E IC在USB 2.0高速(480Mbps)开关中的应用而设计。评估板将一路USB信号切换至两个A类USB端口其中的一路。
MAX4983E评估板PCB上安装了MAX4983EEVB+。
特征
- USB供电(包含电缆)
- 完整的USB 2.0 (480Mbps)切换电路
- 板上VBUS电源开关电路
- 无铅,RoHS兼容
- 经过验证的PCB布局
- 完全安装并经过测试
描述
The USB2GPIO# adapter board is designed to work with Maxim’s Munich GUI and to connect to various EV kit or Pmod boards with Pmod™ compatible connectors for I2C/SPI/GPIO communication to test and evaluate different Maxim ICs. This document explains how the USB2GPIO# adapter board receives commands from a laptop through the USB to create an I2C/SPI/GPIO interface. The Maxim USB2GPIO# board requires the Munich GUI which can be downloaded from Maxim’s website free of charge.
The USB2GPIO# design is powered directly from the USB bus power (5V) and integrates two low-power, 1.2A, PWM step-down DC-DC converters (MAX1556) to provide programmable VCC voltages of 1.8V, 2.5V, 3.3V, or 5.0V. A dual, high-speed, USB-to-multipurpose UART/FIFO IC (FT2232HQ), high-speed USB switches (MAX4983), and a 4K MICROWIRE-compatible serial EEPROM are the other ICs on this adapter board.
USB2GPIO# is designed to supersede USB2PMB1# and USB2PMB2# adapters and includes two connectors; connector X3 is a 12-pin connector which supports either I2C with 6 GPIO pins, or SPI with 4 GPIO pins, and is fully compatible with previous adapters and low-pin count EV kit or Pmod boards. This connector is controlled from the Munich GUI. The addition of another connector, X2, which is a 20-pin connector allows either 16 extra GPIO connections or a second SPI port and 12 extra GPIO connections. This 20-pin connector is NOT controlled by Munich GUI but is for use with future EV kits and will be controlled by the relevant EV kit GUIs.
This USB2GPIO# adapter board can be used to enable USB-to-I2C/SPI interface for any Pmod-compatible plug-in peripheral modules such as the Maxim MAX14001PMB#, and MAXREFDES12 – Corona reference designs. In addition, it can be ordered together as an evaluation system (EV system) with different EV kits, such as MAX14001EVKIT#. Note that an “EV system” is an EV kit combined with an interface board, such as a USB2GPIO# and EV kit GUI software. Ordering information for EV systems is included in the EV kits’ corresponding data sheet. Refer to the appropriate EV kit data sheet for quick start and detailed operating instructions.
The USB2GPIO# has been tested on Windows® 7, Windows 8, and Windows 10 system using Munich GUI, Version 2.17 or later.
查看详情特征
- USB-to-I2C/SPI/GPIO Interface
- Small PCB area
- Pmod-Compatible Form Factor
参量
Protocol | USB Full-Speed USB High-Speed USB Low-Speed |
Configuration | 2-to-1 DPDT |
# Channels | 2 |
VSUPPLY (Single) (V) (min) | 2.8 |
VSUPPLY (Single) (V) (max) | 5.5 |
VSIGNAL (V) (min) | 0 |
VSIGNAL (V) (max) | 5.5 |
Dynamic Range (max) (V) (max) | 5.5 |
RON (Ω) (max) | 10 |
RFLAT(ON) (Ω) (typ) | 0.1 |
Package/Pins | ULTRA TQFN/10 |
Budgetary Price (See Notes) | $2.48 @1k |
主要特征
- USB高速开关
- COM端具有ESD保护
- ±15kV人体模型
- ±15kV IEC 61000-4-2气隙放电
- ±8kV IEC 61000-4-2接触放电
- 工作电源范围:+2.8V至+5.5V
- 5Ω (典型值)的低导通电阻(RON)
- -3dB带宽:950MHz (典型值)
- 兼容低至1.4V的逻辑I/O
- COM模拟输入端具有+5.5V的短路故障保护
- 0.6µA (典型值)的低电源电流
- 使能输入:
- MAX4983E:低电平有效(/EN)
- MAX4984E:高电平有效(EN)
- 小尺寸、10引脚、1.4mm x 1.8mm UTQFN封装
应用/用途
- 总线切换
- 蜂窝电话
- 数码相机
- GPS
- 笔记本电脑
- PDA
- 视频开关
描述
MAX4983E/MAX4984E双刀/双掷(DPDT)开关完全工作于+2.8V至+5.5V单电源,COM1和COM2具有+5.5V的短路保护。该特性使MAX4983E/MAX4984E完全符合USB 2.0规范中的VBUS故障保护要求。这些器件具有较低的逻辑门限电压输入,可用于具有低I/O电压的系统。MAX4983E具有低电平有效的使能输入(/EN),当该引脚为高电平时,器件进入关断模式。MAX4984E具有高电平有效的使能输入(EN),当该引脚为低电平时,器件进入关断模式。器件处于关断模式时,静态电源电流降低至0.1µA。
MAX4983E/MAX4984E采用节省空间的10引脚、1.4mm x 1.8mm、UTQFN封装,工作在-40°C至+85°C温度范围。
技术文档
数据资料 | 高速USB 2.0开关,具有±15kV ESD保护 | Feb 26, 2010 |