关键词: PCB design, PCB design layout, PCB checklist, quad flat pack, quad flat package, QFN assembly, QFN fabrication
The QFN or Quad Flat package No leads is an industry standard in plastic molded packages.
QFN packages have the following advantages:
|Figure 1a. QFN Isometric Top View.||Figure 1b. QFN Isometric Bottom View.|
|Typical Lead Pitch||Control 0.5mm/Power 1.0mm|
|Package Total Height||0.95mm|
Moisture Sensitivity Classification
|MSL 1∼2 Depending on Package Size|
The QFN is shipped in standard polycarbonate conductive carrier tape with pressure-sensitive adhesive cover tape.
The tape and reel is sealed inside an ESD bag. A flat cardboard box is used to store the sealed bag with the appropriate label.
A well-designed and manufactured printed circuit board (PCB) is required for optimum manufacturing yields and product performance.
Two types of land patterns are used for surface-mount devices:
Maxim Integrated recommends the use of SMD pads for all integrated power devices to achieve optimum performance. SMD pads allow for greater copper trace width, which yields lower electrical and thermal resistance. QFN products that do not include integrated power devices (i.e., controllers) can use NSMD pad design.
There should NOT be any mixture of SMD and NSMD pads within the same QFN footprint.
Keeping with good Design For Manufacture (DFM), Maxim Integrated recommends the inclusion of fiducial marks in proximity to the QFN package to facilitate component placement.
Figure 2. Example of Land Pattern.
Maxim's land pattern drawings for QFN packages can be downloaded from our website on the Package Information page. The IPC land pattern calculator (IPC-7351) can be downloaded from the IPC website at: www.ipc.org.
Maxim recommends not to design traces (without solder mask), vias (untented with solder mask) on a printed circuit board (PCB) close to the package lead terminal, and corners underneath the package where tie bars terminate. Refer to IPC-7351 for "Land pattern to via relationship" design recommendation.
Another important consideration in the PCB fabrication process should be the control of the solder mask opening size on the SMD pads.
Failure to comply with this recommendation may result in insufficient solder at the joint, leading to open connections or compromised solder joint reliability.
Selection of an appropriate PCB pad surface finish is critical to ensuring optimum manufacturing of the final board assembly. Table 2 compares several popular surface finishes and summarizes Maxim Integrated's experience with each.
The stencil thickness and pattern geometry determine the precise volume of solder paste deposited onto the device land pattern. Stencil alignment accuracy and consistent solder volume transfer is critical for uniform solder reflow. Stencils are usually made of stainless steel.
To enhance solder paste release, the walls of the apertures should be as smooth as possible. In addition, rounded corners and a trapezoidal cross-section enhance the release of solder paste from the aperture.
Maxim Integrated recommends the following:
Figure 3. Stencil Sample.
Stencil design for E-type land pattern:
Pads are broken into multiple stencil apertures to reduce the paste volume (Figure 4) if it has an E-type package land pattern (shown in Figure 5).
Figure 4. Example of E-type Package Outline (Left) and Stencil Aperture Design (Right). Blue color indicates solder mask openings. White color indicates stencil apertures.
A low-residue, no-clean solder paste is commonly used in mounting QFNs. Water-soluble flux materials are not recommended as there is minimal stand-off (distance of package to PCB) and it will, therefore, be very difficult to clean flux trapped underneath the package.
A Type 3 (or finer) solder paste is recommended for 0.5mm pitch printing.
Maxim Integrated's recommended solder pastes are as follows:
An automatic or manual stencil/screen printer can be used to distribute the solder paste onto the PCB lands.
A Design of Experiment (DOE) should always be used to establish optimum printing parameters. Most assemblers find that the following parameter ranges serve as good starting points:
A stainless steel squeegee should be used.
Multiple printing of solder paste should be avoided for fine pitch devices as it may cause smearing of the solder paste.
Conventional placement systems can be employed using either the QFN outline or the position of the leads as a placement guide.
Figure 5. PCB Example of E-type package.Table 2. Surface Finish Options
|Copper OSP||Organic Solderability Preservative (OSP)||Acceptable|
|Silver Immersion||Thin-layer sliver electroless plated||Acceptable||Silver immersion thickness must be controlled to 0.150～0.625µm to minimize micro voids at the solder joint.|
|Gold Immersion||Thin-layer gold electroless plated||Acceptable|
|HASL||Hot air solder leveled||Acceptable||Vendor's process must be controlled to provide solder coverage of small solder mask openings.|
|Reflow Profile||Description of Characteristics||Process Windows|
|Preheat||Initial heating of component solder balls||2°C to 2.5°C/s|
|Thermal Soak||Solder paste dries out and flux activates||150°C to 170°C, 95 to 100 sec|
|Reflow||Time above 183°C
Peak reflow temperature
|55 to 60 seconds, ～220°C|
|Cooling||Cooling rate||Max -4°C/s|
Figure 6. Eutectic Solder Reflow Temperature Profile.Table 4. Temperature Profile Guideline
|Reflow Profile||Description of Characteristics||Process Windows|
|Preheat||Initial heating of component leads||2.0°C to 2.5°C|
|Thermal Soak||Solder paste dries out and flux activates||150°C to 190°C, 80s to 85s|
|Reflow||Time above 217°C/Peak reflow temperature||70s to 75s/237°C|
|Cooling||Cooling rate||Max - 4.95°C/s|
Figure 7. Lead-Free Solder Reflow Temperature Profile.
Maxim QFNs are compatible with all industry-standard solder reflow processes. There are no special requirements for reflowing QFNs. As with all surface-mount devices, it is important that profiles be checked on all new board designs. Additionally, if there are tall components mixed on the board, the profile must be checked at different locations on the board. Component temperatures may vary due to surrounding components, locations of parts on the PCB, and package densities.
The reflow profile guidelines are based on the temperature at the actual lead to PCB land pad solder joint location. The actual temperature of the solder joint is often different than the temperature settings in the reflow system. It is important that reflow-specific profiles be done using thermocouples at the actual solder joint locations and characterized using the reflow guidelines outlined in Table 3 and Figure 6 for eutectic solder, and Table 4 and Figure 7 for lead-free solder.
Post-reflow inspection of QFNs on PCBs is typically accomplished by using transmission-type X-ray equipment. X-ray can be used for reflow process monitoring and as a failure analysis tool.
A 2-D X-ray system with Oblique View at Highest Magnification (OVHM) is highly recommended as it can detect solder bridges, opens, and voids. Solder joint visual inspection–as in any leaded package technology, the leads are either punch or saw singulated by design and, therefore, the edges of the leads will have bare copper exposed. Lack of solder welting in this area is not considered a criteria for visual inspection/rejection.